[Avail] ABU Microcast Spool for Morrum SX 1600C/1601C Hi-Speed [SXHS1618R]
![Photo1: [Avail] ABU Microcast Spool for Morrum SX 1600C/1601C Hi-Speed [SXHS1618R] (1)](https://www.hedgehog-studio.co.jp/phone/data/hedgehog-studio/product/20240214_78a75f.jpg)
Our Selling Price: US$92.40 [Regular Price: US$132.00]
Item Description
ABU Morrum SX 1600C/1601C for Hi-Speed
Model Name
MS_SXHS1618R
Product Introduction
This microcast spool is exclusively for ABU Morrum SX 1600C/1601C Hi-Speed (centrifugal brake type).
The spool weight and line capacity have been reduced to lighten the entire spool significantly.
This improves the spool response, enables the casting of light lures such as 5 g - 2 g, and increases the casting distance of lures of the same weight.
Color
Gunmetal
Specs
Basic Specifications
- Spool diameter/width
32 mm / 23 mm
- Spool body material
Super duralumin (colored by anodizing)
- Spool shaft material
Super duralumin (anodized-white)
- Drive pin material
Stainless steel
- Installed bearing
MS_SXHS1618R: Outer diameter 11 mm x Inner diameter 5 mm x Thickness x 4 mm
Genuine: Outer diameter 11 mm x Inner diameter 5 mm x Thickness 4 mm
- Compatible reels
Morrum SX 1600C, SX 1601C Hi-Speed
*Morrum SX MAG/IVCB/ULTRA MAG/ZX series are not compatible
*We do not sell drive pins separately. We cannot respond to inquiries about them.
Therefore, please avoid damaging or losing them when replacing the bearings.
Weight
| Spool | Weight | Weight ratio |
| MS_SXHS1618R | 6.8 g | 54 % |
| Genuine spool | 12.6 g | - |
*The weight may vary slightly depending on the production lot.
*Measured with the centrifugal brake unit removed.
Line Capacity
| PE | #0.4 | #0.6 | #0.8 |
| MS_SXHS1618R | 100 m | 80 m | 60 m |
| Nylon | #1 (4lb) Diameter: 0.165 mm |
#1.5 (6lb) Diameter: 0.205 mm |
#2 (8lb) Diameter: 0.235 mm |
| MS_SXHS1618R | 60 m | 40 m | 30 m |
- Measured using SHIMANO "Pitbull 4 (PE)".
- Measured using Yamatoyo Tegusu Co., Ltd. "Versatile Design (Nylon)."
*The above values are measured by winding the line up to the spool rim C surface.
Laser Marking
The spool side has the "model name" and "line capacity" marked by laser for identification purposes.
Please be careful not to damage or lose the genuine centrifugal brake unit and brake blocks when transplanting them to the Microcast Spool SXHS1618R.
If you are worried, we recommend purchasing the 4P-BRAKE-SXHS (SX Hi-speed compatible) and Brake Block Set for ABU 1.2 mm Diameter Centrifugal Brake.
Caution
This product is a light tackle spool that sacrifices some strength to improve the casting distance of light lures.
Especially when using nylon lines, there is a risk of spool damage due to the swelling and contraction caused by the water absorption characteristic of nylon.
Please be careful not to leave the line wound, apply too much tension when winding the line, press the spool and jerk it when removing a snag, or pull and cut it, as these may also cause damage.
Installation Method
The installation method of MS-SXHS1618R is available on Avail's official YouTube, so please refer to it.
