[Avail] SHIMANO Microcast Spool [ALD1532RI] for 15 ALDEBARAN, 18 ALDEBARAN MGL

Model

Microcast Spool ALD1532RI


Product Description


Reel: 15 ALDEBARAN 51HG
Avail parts already installed on reel
Microcast Spool ALD1532RI Pink
Star drag for 15 ALDEBARAN 50 Pink
Mechanical brake knob Pink
Offset Handle LT 80mm Black
M7 Handle nut Black
Wood flat knob Santos Rosewood
GM Knob Cap without Flange Pink



Reel: 15 ALDEBARAN 51HG
Avail parts already installed on reel
Microcast Spool ALD1532RI Sky Blue
Star drag for 15 ALDEBARAN 50 Sky Blue
Mechanical brake knob Sky Blue
Offset Handle LT 75mm Black
M7 Handle nut Black
Wood flat knob Santos Rosewood
GM Knob Cap without Flange Sky Blue


Microcast spool for 15 ALDEBARAN 50 and 18 ALDEBARAN 30.
This spool is equipped with a brake disc on the spool to accommodate a magnetic brake.
The magnetic brake can be adjusted externally using an external dial for SVS Infinity.

Please note that the 15 ALDEBARAN can be used with the genuine SVS Infinity transplanted, but not the 18 ALDEBARAN NEW SVS Infinity when used with centrifugal brakes.

18 ALDEBARAN MGL users should use the optional magnet brake (Microcast Brake ALD15K).


Color

Microcast Spool ALD1532RI


Black


Red


Purple


Blue


Sky Blue


Champagne Gold


Pink


Back view


Spec

Basic Specifications

- Material
Spool portion: Super duralumin (colored by anodizing)
Shaft portion: Super duralumin

- Main size
Microcast Spool ALD1532RI
Spool rim level: 3.2 mm

- Compatible reels
18 ALDEBARAN MGL 30/31 (Genuine SVS cannot be used.)
18 ALDEBARAN MGL 30HG/31HG (Genuine SVS cannot be used.)
15 ALDEBARAN 50/51
15 ALDEBARAN 50HG/51HG

To ensure the strength of the spool shaft, the bearing installed is 10 (outer diameter) x 4 (inner diameter) x 4 (width).

Please note that 15 ALDEBARAN (SVS Infinity) and 18 ALDEBARAN (NEW SVS Infinity) are not compatible.

Customers using 18 ALDEBARAN MGL should use the optional magnet brake (Microcast Brake ALD15K).

- Weight

Spool/Weight/Weight ratio
Microcast Spool ALD1532RI/6.6 g/62.8%
Genuine spool/10.5g/-

Weight may vary slightly depending on the production lot.

Microcast Brake ALD15 Brake 6.0g

Both genuine spools and Avail spools were measured without SVS.


- Line Capacity
8Lb φ0.235mm 70m
10Lb φ0.260mm 60m

Measurements were taken using fluorocarbon line (FLUORO VALUESTAR) manufactured by Yamatoyo Tegusu Co., Ltd.


Attention

* If you feather the reel with your thumb using the spool rim, the alumite may come off due to friction.
Feather a reel with your a thumb, use the spool's spool surface.
When winding line onto the spool, applying too much tension can cause damage.
When winding a stretchy line such as nylon line, in particular, please use a looser tension.


How to use SVS Infinity with implantation

Please refer to the [Avail] SHIMANO SVS Infinity 4 puller product page for SVS Infinity porting instructions.


How to attach the Magnet Brake

It is natural that SHIMANO’s outside dial is not considered to be matched to Avail’s magnet brake system as SVS infinity is made to be functioned smoothly.
Hence, when you adjust the brake dial correctly to 1 or 2, almost no brake is available.
But, it is not defective.
Adjust the brake function as long as it is available and use it.



Detach the side cover from the reel body and take 3 bolts from the Frame B set inside.
1 of 3 fixing bolt which is existed opposite side of outside dial is shorter than others.




Flip the detached frame B set, click the dial, then set the brake pipe condition gear at the peak position.
Then remove the fixing bolt in the center of the dial.




Remove the brake pipe gear by pushing it from the back side.
As the gear tooth is caught in the screw shape cut, further clicking dial is required when it is difficult to remove it.




Insert the inner claws of the magnet brake body into the slit in the frame receiver B set and screw it in.
Screw in to the deepest position.




Install the dials so that the 4 on the external dial is in the position shown in the photo.
At this time, set the dial with fixing bolts.




Once you have reached this point, all you need to do is assemble it.
Fix the 3 points of the frame B set with fixing bolts.




After assembly, adjust the mechanical brake.
Adjust the mechanical brake after installing the spool, and loosen a bit from the position which spool does not wobbly from side to side.