Bearing exchange method of Tatura HLC
Tattoo La series (normal · HD · HLC) is, how to replace any reel also bearings are common.
Loosen the brake dial screw on the brake dial portion of the side cover and remove the side cover.
Then, it can be decomposed into the reel body-side cover spool.
Place to exchange this time bearing will be the mechanical brake knob portion and the side cover.
Tatura does not have bearing is attached to the spool shaft portion.
Also, please note that it can not be attached in addition.
Of you to prepare only precision flat-blade screwdriver to be used when removing the replacement bearing two and the bearing stopper ring.
Bearing How to replace the side cover plate portion
First, remove the bearing stopper ring of the arrow (pentagon of the wire ring).
Precision a flathead screwdriver addressed as shown in the photo to a piece of the bearing stopper ring, you can remove and scoop up from the bottom while pressing a little to the inside of the bearing stopper ring.
In this case, bearing stopper ring can prevent the loss of parts and to work while pressing lightly with the opposite finger. Even if you if you lose unexpectedly spare bearing stopper ring We are also ready.
Bearing stopper ring after removal of the and take out the genuine bearing.
At this time, the handle knob cap remover is easy to recommend because it can be taken out by hooking the bearing With such.
By removing the bearing stopper ring enables genuine bearing is taken out exchange.
After installing the replacement bearings and snap it into the inside of the groove and push the bearing stopper ring finger.
Please try to be working again push the bearing to the back if the bearing stopper ring does not fit well.
Each part is the successful work completed if attached without any problems.
Bearing exchange method of internal mechanical brake knob
Bearing of the mechanical brake knob part of Tatura is different from the normal reel, only remove the mechanical brake knob will not be able to remove the bearing.
Since there is a need to remove the bearing from the inside of the reel body, it describes a simple procedure to disassemble the reel body.
First, remove the handle body and the star drag first.
Next, remove all such as washers and bearings.
Remove the three screws that secure the side cover.
When broken down here you can remove the side cover from the reel body, to retrieve the bearing.
Precision a flathead screwdriver addressed as shown in the photo to a piece of the bearing stopper ring, you can remove and scoop up from the bottom while pressing a little to the inside of the bearing stopper ring.
※ Tatura CT · Tatura CT type case of R
Tatura CT · Tatura CT Type R is bearing the mechanical brake knob portion has been fixed in the parts of the bearing retainer.
Bearing stopper ring and the shape is different, but this part even with a precision flat-blade screwdriver, you can be removed if to scoop up the parts from the bottom.
In this case, bearing stopper ring can prevent the loss of parts and to work while pressing lightly with the opposite finger. Even if you if you lose unexpectedly spare bearing stopper ring We are also ready.
Bearing stopper ringAfter removal of the and take out the genuine bearing.
At this time, the handle knob cap remover is easy to recommend because it can be taken out by hooking the bearing With such.
By removing the bearing stopper ring enables genuine bearing is taken out exchange.
After installing the replacement bearings and snap it into the inside of the groove and push the bearing stopper ring finger.
Please try to be working again push the bearing to the back if the bearing stopper ring does not fit well.
This bearing exchange will be completed.
Followed by the side cover and star drag, it will restore the handle.
First, install the drag color to the handle shaft. In this case, please let engage properly projections of the drag color into the holes of the drag disc washer.
Tighten the three screws to secure the side cover.
Attach it to the handle shaft in the order of bearings and washers (silver).
Attach the sound out holder to the handle shaft.
Attach it to the handle shaft in the order of the dish washer two and washer (gold).
Dish washer please go to each attachment in the opposite direction as shown in the photograph.
Install the fixing nut and the spring on the handle shaft.
Install the star drag and washer to the handle shaft.
Please perform the attachment to fit in it because there is a groove aligned with the securing nut on the inside of the star drag.
Finally, secure the handle, built-in the spool and side cover, please check whether there is a problem with the operation.