PX68 bearing How to Replace
Loosen the brake dial screw on the brake dial portion of the side cover and remove the side cover.
Then, it can be decomposed into the reel body-side cover spool.
Of you to prepare only precision flat-blade screwdriver to be used when removing the replacement bearing two and the bearing stopper ring.
Bearing How to replace the side cover plate portion
First, remove the bearing stopper ring of arrows.
Precision a flathead screwdriver addressed as shown in the photo to a piece of the bearing stopper ring, you can remove and scoop up from the bottom while pressing a little to the inside of the bearing stopper ring.
In this case, bearing stopper ring can prevent the loss of parts and to work while pressing lightly with the opposite finger. Even if you if you lose unexpectedly spare bearing stopper ring We are also ready.
Bearing stopper ring after removal of the and take out the genuine bearing.
At this time, the handle knob cap remover is easy to recommend because it can be taken out by hooking the bearing With such.
By removing the bearing stopper ring enables genuine bearing is taken out exchange.
After installing the replacement bearings and snap it into the inside of the groove and push the bearing stopper ring finger.
Please try to be working again push the bearing to the back if the bearing stopper ring does not fit well.
It is successfully completed work if each part is attached as shown in the photograph.
Bearing exchange method of the spool shaft portion
Bearing of the spool shaft section also allows you to exchange With the spool bearing remover.
The removal of the shaft pin spool bearing remover you used.
※ spool bearing remover more information on how to use, please refer to the product page.
After removing the shaft pin, and remove the bearing from the housing.
Bearing stopper ring is fixed at, but precisely a flathead screwdriver addressed as shown in the photo to a piece of the bearing stopper ring, you can remove and scoop up from the bottom while pressing a little to the inside of the bearing stopper ring.
In this case, bearing stopper ring can prevent the loss of parts and to work while pressing lightly with the opposite finger. Even if you if you lose unexpectedly spare bearing stopper ring We are also ready.
Bearing stopper ring after removal of the and take out the genuine bearing.
At this time, the handle knob cap remover is easy to recommend because it can be taken out by hooking the bearing With such.
· AIR HD · AIR · ZR case of bearings
and decomposition so far can remove the bearing from the spool and housing, enables the bearing exchange.
After installing a replacement bearing in the housing and snap it into the inside of the groove and push the bearing stopper ring finger.
Please try to be working again push the bearing to the back if the bearing stopper ring does not fit well.
Attach the bearing to the housing each spool shaft.
※ Caution
When you do embedded in a state that does not attach the housing to the bearing, cause of failure not spool to neatly operation after assembly.
The occasion of the built-in , please make sure that you always housing is attached to the bearing .
After bearing mounting, again the shaft pin spool bearing remover is the work completion be attached using.
Finally, the assembly of the reel, please perform the operation check whether there is a problem.
If the AIR BFS bearing of the mounting
When broken down here can remove the bearing from the spool and housing, it enables the bearing exchange.
Washer such installation of the AIR BFS bearing is separately supplied with the bearing body also do the installation.
After installing a replacement bearing in the housing and snap it into the inside of the groove and push the bearing stopper ring finger.
Please try to be working again push the bearing to the back if the bearing stopper ring does not fit well.
Attach the silver washer and black plastic ring to the spool shaft before mounting the bearing to the spool. The order in which install, please note that the silver washers will be the first.
Attach the bearing to the housing each spool shaft.
※ Caution
When you do embedded in a state that does not attach the housing to the bearing, cause of failure not spool to neatly operation after assembly.
The occasion of the built-in , please make sure that you always housing is attached to the bearing .
After bearing mounting, again the shaft pin spool bearing remover is the work completion be attached using.
Finally, the assembly of the reel, please perform the operation check whether there is a problem.